← Back
NotesComplete setEnglish

Completed notes of the course

Complete course materials for Turbomachinery in the Mechanical Engineering degree programme at Politecnico di Milano. The document covers: Turbomachinery Illustrated, Source-Audited Study Notes Based on the lecture presentations of Prof. P. Gaetani Politecnico di Milano Consolidated study document Consolidated revision with Turbines – 4 November 2026 How these notes are organised These notes are written in English

TurbomachineryComplete set

Document information

What's included in this study material

Complete course materials for Turbomachinery in the Mechanical Engineering degree programme at Politecnico di Milano. The document covers: Turbomachinery Illustrated, Source-Audited Study Notes Based on the lecture presentations of Prof. P. Gaetani Politecnico di Milano Consolidated study document Consolidated revision with Turbines – 4 November 2026 How these notes are organised These notes are written in English

Import quality: text was extracted directly from the original document.

Extracted content from the document

Representative passages recognised in different parts of the material. The full extracted text remains available to search, while this compact preview makes the page easier to read.

Page 1

Turbomachinery Illustrated, Source-Audited Study Notes Based on the lecture presentations of Prof. P. Gaetani Politecnico di Milano Consolidated study document Consolidated revision with Turbines – 4 November 2026

Page 35

Turbomachinery Chapter 1. Fundamentals for Turbomachinery The momentum thickness measures the momentum-flux deficit: Z δ ρu u   θ= 1− dy. (1.13) 0 ρδ U U Rδ For constant density, θ = 0 (u/U )(1 − u/U ) dy. The kinetic-energy thickness measures the deficit in kinetic-energy flux: ! u2 Z δ ∗∗ ρu δ = 1− 2 dy. (1.14) 0 ρδ U U The lecture’s shape factor is δ∗ H= . θ For a dynamically similar family of velocity profiles u/U = f (y/δ), H is a useful profile-shape parameter. It is not a direct measure of boundary-layer thickness: two layers can have the same δ but different H and different momentum deficits. 1.26 Skin-friction coefficients and flat-plate drag The wall shear stress is τw . The local skin-friction coefficient and the average coefficient over a plate of length l are Z l τw dx τw c′f = 1 2 , cf = 0 1 2 . 2 ρU 2 ρU l For the zero-pressure-gradient flat plate considered in the lecture, an integral momentum balance on the boundary layer gives dθ 2θl c′f = 2 , cf = CD = . (1.15) dx l The second expression follows by integrating the local relation from the leading edge to x = l, with θ = 0 at the ideal leading edge. It connects the total drag coefficient of the plate with the momentum thickness at the trailing edge. 1.27 Von Kármán momentum-integral equation The lecture obtains the integral boundary-layer equation from the two-dimensional, steady, in- compressible boundary-layer equations. Let x be streamwise and y wall-normal. The thin-layer assumptions are δ ≪ L, v ≪ u, and wall-normal gradients dominate streamwise gradients. The pressure is approximately uniform across the boundary layer, so p = p(x) and the external inviscid velocity U (x) satisfies dp dU = −ρU . dx dx The streamwise momentum equation within the layer is ∂u ∂u dp ∂τ ∂u   ρ u +v =− + , τ =µ . ∂x…

Page 70

Turbomachinery Chapter 4. Turbomachinery Fluid Dynamics Figure 4.10: Disk-friction coefficient versus non-dimensional disk-to-wall clearance for several Reynolds numbers (Lecture 4C, slide 35). 4.20 Loss accounting and annular-cascade measurement A total loss budget can be separated into profile, annulus, secondary, leakage/recirculation, disk friction and (when relevant) shock losses. The contributions can be summed only when their reference states and normalisations are consistent. Measurements are made at downstream traverse planes where flow non-uniformity is expected; finer measurement grids are needed near wakes, endwalls and leakage vortices. A map of total pressure, Mach number and flow angle is more informative than a single mass-averaged value because it shows where the loss is generated. Key points Chapter 4: what must be understood. Explain the three flow surfaces; derive cascade force from momentum and Bernoulli; understand solidity, stagger, incidence and deviation; distinguish slip from dissipation; derive radial equilibrium and ISRE/NISRE; compare constant-angle/free-vortex/forced-vortex distributions; and explain how wakes, endwall flows, tip leakage, labyrinth seals and disk friction create losses. Lecture source: 4A, slides 3–30; 4B, slides 3–29; 4C, slides 3–49.. 54

Page 105

Turbomachinery Chapter 9. Turbines Turbine rows usually have larger flow turning and higher blade loading than compressor rows. From the angular-momentum balance, a larger change in tangential velocity increases the force and work exchanged per unit mass. The lecture’s design-level conclusion is that turbines can transfer more work per stage and therefore may require fewer stages for a prescribed total enthalpy change. This is a trade-off, not a statement that arbitrarily large turning is desirable: higher loading also increases profile, secondary-flow and clearance losses, which are treated below. Figure 9.4: Compressor blade-surface pressure-coefficient distribution and turbine passage/throat geometry (Turbines, slide 11). 9.4 Axial gas and steam turbine stage design 9.4.1 Dimensionless quantities and design ranges For the axial turbines considered in the lecture, the blade peripheral speed is treated as approxi- mately constant across a row. The flow coefficient and peripheral-velocity coefficient are Vm,1 U ϕ= , Kp = . U V1 The lecture uses several head/work-coefficient normalisations. In particular, hT,0 − h2,is hT,0 − h2,is ψ= or ψ = , U2 U 2 /2 while the positive turbine work coefficient can be written Lu Vt,1 − Vt,2 λ= = U2 U for a constant-U axial stage and the turbine extraction convention. If the denominator is U 2 /2, the numerical coefficient is twice the value based on U 2 . The source’s different definitions must not be mixed when comparing charts or numerical data. The source also gives Balje specific-speed and specific-diameter definitions: √ ω Qout (∆his )1/4 Ωs = ωs = , D s = Dtip √ . (∆his )3/4 Qout These non-dimensional/derived design parameters help classify the turbine family and relate the desired flow and enthalpy drop to rotational speed and…

Page 140

Source material All source-derived content is based on the lecture presentations by Prof. P. Gaetani, Politecnico di Milano: Fundamentals for Turbomachinery (1A, 1B, 1C); Fundamentals of Turbomachinery (2A, 2B); Similitude in Turbomachinery; Turbomachinery Fluid Dynamics (4A, 4B, 4C); Diffusers; Centrifugal Compressors; Axial Compressors; Instabilities in Compressors; and Turbines. 124

Preview

First page of the document.

First page: Completed notes of the course